Improve Workforce Efficiency

Course #: 5602A-F
Duration: 60 hours
What Students Learn: PART 1 (5602A). Growth and Manufacture of Wood; Classification of Hardwoods and Softwoods; Grading of Softwoods and Hardwoods; Qualities of Wood; Use of Joist Table.
PART 2 (5602B). Framing Methods; Joints in Wood Frame; Floors, Walls, and Roof Construction; Fastening the Wood Frame; Forms for Concrete; Protection Against Fire Control of Decay and Termites.
PART 3 (5602C). Roof Decks; Roof Framing Systems; Materials of Construction; Joists, Beams, and Rafters; Roof Trusses; Timber Arches; Miscellaneous Framing Systems; Erection.
PART 4 (5602D). General Requirements of Exterior Finish; Exterior Finish of Walls; Cornices; Windows; Masonry, Brick Veneer, and Stucco.
PART 5 (5602E). Thermal Insulation; Condensation Control; Sound Insulation and Acoustical Treatment.
PART 6 (5602F). Kinds of Wood and Types of Flooring; Strip Flooring; Plank, Block, and Parquet Flooring; Installation of Wood Flooring; Flooring Problems; Installation of Interior Finish.

Course #: Block D20
Duration: 40 hours
What Students Learn: The eight lessons in this block provide the trainee with the skills and knowledge needed to perform those tasks associated with the trades of plumber and pipefitter. The program includes coverage of the most widely accepted materials used for pipe, fittings, and valves. The trainee will learn how to use the tools of the trades, with an emphasis on safety. In addition, the methods used to join pipe, and the procedures for supporting, installing, and testing piping systems, are discussed in detail. Common plumbing fixture installation and maintenance, along with a review of tanks, pumps, and boilers, are covered.
Components: The Trades of Plumbing and Pipefitting (286040); Pipes, Fittings, and Valves (286041); Plumbing and Pipefitting Tools (286042); Joining and Assembling Pipes (286043); Supporting, Installing, and Testing Pipes (286044); Plumbing Fixtures and Appliances (286045); Tanks, Pumps, and Boilers (286046); Insulation for Piping and Ducting (286047);
Special Notes: This updated course replaces Industrial Plumbing and Pipefitting, Block D10. Each study unit contains a progress examination.

Course #: 286040
Duration: 5 hours
What Students Learn:

• Identify the differences between "plumbing" and "pipefitting."
• Discuss the basic concepts of codes and standards.
• Relate information about the different types of mechanical systems in buildings.
• Demonstrate basic skills for blueprint reading.
• Identify the terms: blueprints, architectural drawings, working drawings, manufacturers' specifications and job specifications.
• Relate the basic concepts of blueprint reading.
• Use a measuring scale.
• Identify symbols and abbreviations used on working drawings.
• Locate specifications pertaining to a specific material or system.
• Explain how different types of plumbing and piping systems are categorized.
  

Course #: 286041
Duration: 5 hours
What Students Learn:

• Identify and classify the different types of material that are used to manufacture pipes, fittings, and valves.
• List the characteristics of the various types of pipes, fittings, and valves available.
• Classify and identify pipe "markings."
• Know how to "read" a fitting for ordering purposes.
• Identify the various types of valves and know their components.
• Perform basic valve maintenance and know proper installation techniques.
• Select and specify pipes, fittings, and valves for a particular application.
  

Course #: 286042
Duration: 5 hours
What Students Learn:

• Identify the various tools available for various tasks by appearance.
• Demonstrate your knowledge of job safety and tool safety.
• Identify the tools required to join and assemble pipes of different material composition.
• Determine when and how to use pipe-joint assembly tools.
• Identify the tools required to perform layout, cutting, and boring tasks.
• Identify the tools needed for testing and maintaining piping systems.
• Determine when and how to use finishing, testing, and maintenance tools for piping systems.
  

Course #: 286043
Duration: 5 hours
What Students Learn:

• List necessary precautions to be taken when working with materials or procedures to join pipes.
• Cut pipe lengths manufactured from the various pipes materials, as required by a piping system layout.
• Prepare and assemble the various pipe joints you learned earlier.
• Identify the materials, tools, and equipment needed for pipe.
• Perform basic pipe welding tasks.
  

Course #: 286044
Duration: 5 hours
What Students Learn:

• Lay out, install, and align a piping system either inside a building or underground.
• Properly support a piping system using the various available methods, taking into account thermal expansion and contraction.
• Identify methods and materials used to protect piping installations.
• Calculate pipe offsets to avoid obstructions when laying out and installing a piping system.
• Test different types of piping systems for defective materials or faulty workmanship.
  

Course #: 286045
Duration: 5 hours
What Students Learn:

• Recognize trade terms used to categorize and describe plumbing components.
• Identify the different types of plumbing fixtures, trim, appliances, and appurtenances.
• Explain the procedures used for installing plumbing fixtures and trim.
• Discuss common maintenance problems and corrective action for plumbing components.
  

Course #: 286046
Duration: 5 hours
What Students Learn:

• Identify and classify the various available tanks.
• Specify and size round and rectangular tanks, and sumps, for a particular application.
• Identify different pumps and know pump principles.
• Discuss pump installation, start-up, and maintenance procedures.
• List the characteristics of boilers and discuss their classifications.
• Identify boiler accessories and know basic boiler maintenance.
  

Course #: 286047
Duration: 5 hours
What Students Learn:

• Identify and understand the function and types of different piping and ducting insulation materials.
• Select the proper insulation type, material, and thickness for a given piping system.
• Properly cut, form, and install insulation and shielding to piping and ducting.
  

Course #: 6447A-B
Duration: 20 hours
Course Prerequisites: Basic Industrial Math (Block X21); Practical Measurements (Block X22);
What Students Learn: PART 1 (6447A). Basic Principles and Matter; Sources of Heat and Measurement of Temperature; Heat Transmission and Measurement; Effects of Heat; Heat and Properties of Mixtures; Heat and Work; Combustion and Heat; Steam.
PART 2 (6447B). Weight and Pressure of Gases; Energy, Motion, and Air Velocities; Air and Air Mixtures; Air Movements and Ventilation; Air Conditions and Air Conditioning.

Course #: 6084A-B
Duration: 20 hours
What Students Learn: PART 1 (6084A). Comfort Air Conditioning; Heat Transmission through Buildings.
PART 2 (6084B). Types of Equipment; Air Distribution Systems; Automatic Controls and Cooling Systems; Noise Elimination, Zoning, and Special Conditions; Heat Pump.

Course #: 5004C
Duration: 10 hours
What Students Learn: Fitting Practice; Tolerance, Allowance, Clearance, and Fit; Babbitting; Hack Saw; Band Saw Machine; Clamping Work for Sawing; Soldering; Soft Solder; Soldering Copper; Sweat Soldering; Brazing; Hand Solders and Fluxes; Torch Brazing; Induction Brazing; Furnace Brazing.

Course #: 286016
Duration: 10 hours
What Students Learn: The purpose of this series of study units on rigging is to tell you where and how to stand, to tell you about the basic tools that are available, and to show you how to use the tools to move heavy or awkward objects in a safe and efficient manner. In short, the purpose is to help you understand the basic principles of rigging you'll need in your daily activities on the job.
This first study unit in the rigging series presents an overview of rigging - what it is, what kind of work is involved, who does it - and provides you with a fundamental knowledge of the basic mechanisms used in rigging and of the concepts of mechanical advantage, friction, center of gravity, and weight. Recognizing that the metric system of measurements is widely accepted, we've provided an Appendix which gives metric conversion factors for the English system units used in this text.
When you complete this study unit, you will be able to:

• Describe the theoretical principles of the seven basic mechanisms - inclined plane, wedge, screw, lever, wheel and axle, pulley, and hydraulic ram.
• Solve basic mechanism problems using the concepts of mechanical advantage.
• Solve basic mechanism problems using the concepts of friction loss.
• Calculate the weights of geometric solids.
• Determine the center of gravity of simple plane and solid shapes.

Introduction To Rigging; Basic Mechanisms Used In Rigging; Weight And Center Of Gravity.

Special Notes:
• This updated course replaces course 5030A.
• The entire course consists of study units 286016, 286017, 286018, 286019, 286020 and 286021.

Course #: 286017
Duration: 10 hours
What Students Learn: Equalizing and Distributing Loads; Reasons for and Examples of Load Equalization and Distribution: Basic Methods of Equalizing and Distributing Loads; Planning and Executing a Rigging Job; What You Must Know before starting a Sample Rigging Operation; Safety in Rigging; Rigging Hazards; How to Reduce Hazards.

Special Notes:

• This updated course replaces course 5030B.
• The entire course consists of study units 286016, 286017, 286018, 286019, 286020 and 286021.

Course #: 286018
Duration: 10 hours
What Students Learn: In this study unit, you'll study some of the basic tools and pieces of equipment that are used in typical rigging operations. This unit deals with wire and fiber ropes, and chains. In particular, you'll study about the characteristics and requirements of these common rigging and hoisting tools, and about the procedures and precautions required in their use. Also included are inspection methods, rope splicing, and fiber knot tying.
In the selection of tools and rigging equipment, it pays to obtain quality items. Also, before using any tool or piece of equipment, the rigger is cautioned to become familiar with its operating characteristics and limitations, and the proper handling techniques and required maintenance for the tool. The more complex the tool or piece of equipment, the more certain the rigger should be of its characteristics.
When you complete this study unit, you'll be able to:

• Describe and classify the various types of wire rope and discuss the factors which influence wire rope construction.
• Define the term safety factor and discuss how it relates to safe working load limit.
• Discuss the factors which need to be considered when inspecting wire rope slings.
• Identify the various types of end attachments and describe their application in the rigging operation.
• List the five common types of fiber ropes and discuss their inherent advantages and disadvantages to the rigging operation.
• Contrast the advantages and disadvantages of chain slings with those of wire rope slings.
• Discuss the factors which need to be considered when inspecting chain slings.
• List safety consideration necessary when utilizing wire rope, fiber rope, and chain slings.

Working with Wire Rope, Fiber Ropes, and Chains; Explains the Proper Handling and Care of these Common Rigging Tools; Details Correct Rope Splicing and End-Attachment Procedures.

Special Notes:
• This updated course replaces course 5030C.
• The entire course consists of study units 286016, 286017, 286018, 286019, 286020 and 286021.

Course #: 286019
Duration: 10 hours
What Students Learn: In this study unit, you'll learn how riggers use simple and complex rigging tools to complete a task. This unit explains how slings, hitches, hoists, and various other types of rigging hardware are sized, selected, inspected, and positioned by riggers as they prepare to lift a load. You'll learn how to combine the reeving hardware you've already learned about into safe, effective reeving systems. You'll be introduced to the types of equipment riggers use to move a load along a floor or roadway and learn how they support these loads. This study unit includes an overview of wood grading and inspecting practices. Many riggers must be able to select wooden supports and other items used during lifting or supporting operations. Finally, the unit ends with an in-depth discussion of ladder and scaffold types and specifications.
When you complete this study unit, you'll be able to:

• Identify the various types of slings and recommend where each type can be most effectively utilized for rigging operations.
• Describe the common types of sling hardware and discuss how they're used in the rigging operation.
• Demonstrate how to calculate the efficiency of a reeving system.
• Discuss the use of supporting equipment and demonstrate how to calculate the distribution of pressure.
• Explain the proper use of levers, side plates, rollers, and other equipment in the horizontal movement of a load.
• Describe the various types of ladders and scaffolding and discuss how they can be correctly employed.

Slings And Hitches; Rigging Hardware; Hoists; Reeving; Supporting Equipment; Horizontal Movement Equipment; Knowledge Of Woods Needed By Rigger; Ladders; Scaffolds.

Special Notes:
• This updated course replaces course 5030D.
• The entire course consists of study units 286016, 286017, 286018, 286019, 286020 and 286021.

Course #: 286020
Duration: 10 hours
What Students Learn: In this study unit, you'll learn about cranes and other types of equipment used for heavy lifts. This study unit isn't intended to make you a knowledgeable equipment operator, because every manufacturer's equipment is different, and specialized training on specific types of equipment is always necessary. Rather, the unit is intended to make you familiar with the range of equipment available in the marketplace and help you understand the benefits and limitations of each category of lifting equipment. Some of the more widely used pieces of equipment are described in additional detail so that you'll know more about their inner workings and operation.
When you complete this study unit, you'll be able to:

• Understand the basic principles of crane safety.
• Identify the more common types of cranes and their components.
• Identify the drive members for a crawler-type mobile crane.
• Identify and give the functions of the various parts of a truck-type mobile crane.
• Know how to use crane rating charts.
• Select the correct mobile crane attachment for a particular function.
• Describe a dragline setup and distinguish its parts.
• Describe in general how to set up a boom.
• Select a suitable crane if given a set of specific lift conditions and crane capacity rating tables.

Introduction To Lifting Equipment; Crane Rating Charts; Small Lifting Equipment; Mobile Cranes; Mobile Crane Attachments, Operation And Setup.

Special Notes:
• This updated course replaces course 5030E.
• The entire course consists of study units 286016, 286017, 286018, 286019,
  286020 and 286021.

Course #: 286021
Duration: 10 hours
What Students Learn: This study unit continues the review of lifting equipment. In Part 1, we focused on small lifting equipment (hoists, aerial work platforms, and lift trucks) and on various types of mobile cranes (crawlers, truck-type, floating cranes).
In Part 2, we describe the remaining types of equipment, grouped simply as limited travel cranes, derricks, and specialty cranes. We then present a series of case studies that show how some of the lifting equipment we have studied are actually used in the workplace. The emphasis is on particularly challenging or noteworthy lifts. When available, we have also included information on the rigging techniques employed for these lifts.
After reviewing Lifting Equipment and Applications, Parts 1 and 2, you should have a good general understanding of the range of lifting equipment that you, as a rigger, will encounter at industrial and construction work sites, how this equipment works, and the advantages and limitations of these lifting devices.
When you complete this study unit, you'll be able to:

• Describe the various types of limited travel cranes.
• Distinguish between the functions of derricks in common use.
• Identify the importance of two types of specialty cranes.
• Understand why certain cranes were used in various lifting situations.

Limited Travel Cranes; Derricks; Specialty Cranes; Lifting Equipment Applications; Appendix: Rigging And Lifting Resources.

Special Notes:
• This updated course replaces course 5030F.
• The entire course consists of study units 286016, 286017, 286018, 286019,
  286020 and 286021.

Course #: 4501A-C
Duration: 45 hours
What Students Learn: PART 1 (4501A). Administration; Definitions; Occupancy Requirements; Means of Egress; Restrictions to Buildings and Structures; Environmental Requirements.
PART 2 (4501B). Requirements for Types of Construction; Fire Protection Requirements; Structural Design Requirements of Buildings and Structures; Chimneys, Fireplaces, and Venting Systems; Heat-Producing Appliances; Heating, Ventilating, and Air-Conditioning; Blower and Exhaust Systems; Safeguards During Construction.
PART 3 (4501C). Elevators and Mechanical Equipment; Gas Piping; Electrical Wiring Systems; Signs and Outdoor Display Structures; Requirements for Existing Buildings.